DC Voltage |
|
6.000 V |
0.5% + 3d |
|
60.00 V |
1.0% + 5d |
|
600.0 V |
2.0% + 5d |
NMRR: |
>30 dB @ 50/60 Hz |
CMRR: |
>100 dB @ Dc, 50/60 Hz, Rs=1kΩ |
Hi-Z DCV Input Impedance: |
5 MΩ, 90 pF nominal |
AutoCheck Lo-Z DCV input impedance: |
Initially 1.6 kΩ, 90 pF nominal; impedance increases significantly as
display voltage increases from 50 V (typical). Typical impedances vs display voltages for reference
are 15 kΩ @ 100 V; 100 kΩ @ 300 V; 210 kΩ @ 600 V |
AutoCheck DCV Threshold: |
> +1.5 V DC or < -1.0 V DC nominal |
AC Voltage |
50 Hz/60 Hz |
6.000 V, 60.00 V |
1.5% + 5d |
|
600.0 V |
2.0% + 5d |
50 Hz ~ 500 Hz |
6.000 V, 60.00 V |
2.0% + 5d |
|
600.0 V |
2.5% + 5d |
CMRR: |
>60 dB @ Dc to 60 Hz, Rs=1kΩ |
Hi-Z ACV Input Impedance: |
5 MΩ, 90 pF nominal |
AutoCheck Lo-Z ACV input impedance: |
Initially 1.6 kΩ, 90 pF nominal; impedance increases significantly as
display voltage increases from 50 V (typical). Typical impedances vs display voltages for reference
are 5 kΩ @ 100 V; 100 kΩ @ 300 V; 210 kΩ @ 600 V |
AutoCheck ACV Threshold: |
> 2 VAC (50/60 Hz) nominal. True RMS model ACD-15 RRMS-PRO Crest less
than 1.6:1 at full scale & less than 3.3:1 at half scale |
Resistance |
|
6.000 kΩ 2 |
1.2% + 6d1, 3 |
|
60.00 kΩ, 600.0 kΩ |
1.0% + 4d |
|
6.000 MΩ |
2.0% + 4d |
Open circuit voltage: 0.4 VDC typical |
1Cool down interval 2 minutes after over 50 V measurements
in Auto-VΩ position
2Beeper on while reading < 0.025 kΩ
3Add 40d to specified accuracy while reading is |
600Ω with Continuity Beeper |
|
600.0 Ω |
2.0% + 8d1 |
Continuity beeper response: |
< 100 µs |
Open circuit voltage: |
0.4 VDC typical |
Audible threshold : |
Between 10 Ω and 300 Ω 1) Add 40d to specified accuracy while reading is below 20% of range
|
Frequency |
Range: 10 Hz ~ 30 kHz 0 Hz ~ 1 kHz 10 Hz ~ 1 kHz |
Sensitivity (Sine RMS) 4 V 30 V 60 V |
Voltage Range: 6.000 V 60.00 V 600.0 V |
Accuracy |
0.5% + 4d |
Max display: |
9999 counts |
Diode Tester |
Open circuit voltage |
Test current |
|
less than 1.6 V DC |
0.4 mA (typical) |
|
Audible threshold: |
between 0.15 V & 0.080 V |
|
Capacitance |
|
100.0 nF2, 1000 nF |
3.5% + 5d1, 3 |
|
10.00 µF, 100.0 µF, 2000 µF |
|
1) Accuracies with film capacitor or better |
2) Accuracy below 50 nF is not specified |
3) Specified with battery voltage above 2.8 V (app. half-full battery). Accuracy
decreases gradually to 12% at low battery warning voltage of approximately 2.4 V |
Non-contact EF-detection |
Typical voltage |
Bar graph indication |
|
15 V to 85 V |
- |
|
40 V to 130 V |
-- |
|
60 V to 210 V |
--- |
|
90 V to 300 V |
---- |
|
Above 120 V |
---- |
|
Indication: |
Bar graph segments & audible beep tones proportional to the field
strength |
Detection frequency: |
50/60 Hz |
Detection antenna: |
Top side of the stationary jaw |
Probe-contact EF-detection: |
For more precise indication of live wires, use the red (+) probe for
direct contact measurements |
AC current (clamp-on) |
50 Hz/60 Hz |
400.0 A, 2000 A |
1.5% + 5d |
1) Add 8d to specified accuracy while reading is below 10% of range |
2) Induced error from adjacent current-carrying conductor: < 0.06 A/A |
3) Specified accuracy is for measurements made at the jaw center. When the conductor
is not positioned at the jaw center, position errors introduced are: Add 1% to specified accuracy for
measurements made within jaw marking lines (away from jaw opening) Add 4% to specified accuracy for
measurements made beyond jaw marking lines (toward jaws opening) |